Exploring Basic Plumbing for Installing a Bathtub
Exploring Basic Plumbing for Installing a Bathtub
Blog Article
Each person may have their own unique piece of advice with regards to How to Install a Bathtub.
Installing a bath tub isn't exactly rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a brand-new one is also a moderately hard task. If the old tub is easily accessible, the project can relocate speedily; if you need to open a wall surface to eliminate the old bathtub and position the new bath tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub and also embeded in the new one. See to it you have qualified yourself for the job as well as fit attempting it. As opposed to working with a professional to take control of a halfway-completed job, it is far better to take into consideration employing one before you start. Chances are you may require a professional plumber to make tube links.
This short article will certainly help you install a new bath tub in your shower room if you have currently purchased a new tub and also don't need to change the arrangement of your previous water system pipes.
Your devices and product list ought to comprise the following:
Getting ready for the Setup
To start with, the supporting structure provided with the bath should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its final position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the restricted gain access to that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the remaining water that will originate from the pipelines. As soon as the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. Once the taps have been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Utilizing the two wooden boards under its feet, position the bathtub in the needed position. The wooden boards are helpful in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the tub till the spirit level reviews degree.
To mount taps, fit the bottom of the furthest flexible faucet connector to the ideal supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the water supply and inspect all joints and new pipework for leakages and tighten them if required. Fill the bathtub and additionally examine the overflow outlet and also the normal outlet for leakages.
Lastly, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been used a minimum of when as this will certainly settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in place with the maker given backnut. As soon as the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type needs to be connected to the tap ends initially, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, leading to issues with dampness and possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the tub is in usage. The sealer can break rather early if you do not take into account this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily available on the market. It is recommended to fit the floor tiles making use of water-resistant or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that page on A Step-by-Step Guide to Installing a Bathtub while doing a search on the internet. Those who enjoyed reading our post plz remember to share it. Kudos for your time. Don't forget to come visit our site back soon.
Schedule A Service Call Report this page